50 x 1N4007 1A 1000V Silicon Rectifier Diode (Pack of 50)

Product Information

The company offers a wide range of products, including diodes, rectifiers, transistors, voltage regulators, MOSFETs, LED drivers, and protection devices, among others.

Moreover it can also be used in any general purpose application where there is need of a general diode. The 1N4007 diode is built for working with high voltages and it can easily handle voltage below 1000V. The 1000mA or 1A average fwd current, 3W power dissipation with small size and lost cost also makes it ideal for wide variety of applications. Diodes are used in a circuit to ensure that the electrical current flows in one direction only. Due to this, they are used for converting AC to DC power. A diode is a device which allows current flow through only one direction. That is the current should always flow from the Anode to cathode. The cathode terminal can be identified by using a grey bar as shown in the picture above. For use in general purpose rectification of power supplies, inverters, converters, and freewheeling diodes application.In addition to the reverse voltage, an essential characteristic is the forward current, for 1N4007 it reaches 1A. Theoretically, these diodes could be used in a 220W switching power supply, if a good heat sink from diodes is ensured (for example, by filling them with compound), but one should not go so extreme with these diodes and in the input rectifier of 220W power supply one should not exceed 50-100W, depending on the cooling system efficiency. 1N4007 Analogs From the construction point of view, these are solid-state devices made of semiconductor material that replaced vacuum valves for the rectification of the electrical signal. What is the 1N400X Recifier Diode series? is a general diode that is used as a rectifier in an electronic circuit. It converts the power from AC to DC with a filter capacitor. 1N4007 is designed to work on high voltages and can easily operate with voltages under 1000V.

To obtain the maximum operating time of the diode, it is recommended to always stay between 30 and 40 V below its maximum repetitive reverse voltage and other values. Always connect with correct polarity, do not exceed a load of 1A. Do not operate and store at a temperature below -55 centigrade and above +175 centigrade. a b "M1-M7 Datasheet" (PDF). Diotec Semiconductor. December 2016. Archived (PDF) from the original on 23 February 2018. This blog covers 1N4007 rectifier diode pinout, features, and other information including its advantages, applications and how to use this device, etc.The breakdown voltage of the 1N4007 diode is around 1000 volts. Can I use 1N4007 instead of 1N4148? Since the 1N4007 is made with sufficient pin length, the diode can be mounted vertically or horizontally. A 1N4007 is a widely used general purpose diode. It is normally build to use as rectifier in the power supplies section of electronic appliances for converting AC voltage to DC with other filter capacitors. It is a diode of 1N400x series in which there are also other similar diodes from 1N4001 to 1N4007 and the only difference between them is the max repetitive reverse voltage. Yes, the 1N4007 can be replaced with the 1N4001 diode because both are from the same family of 1N400x diodes. And since the reverse voltage rating of 1000 V for 1N4007 is higher than that of 1N4001(50 V), it’s even better. To get the maximum long run of the diode it is recommended to always stay 30V to 40V below from it max repetitive reverse voltage and other values. Always connect in right polarity, do not drive more than 1A load. Do not operate and store in temperature below -55 centigrade and above +175 centigrade.

The 1N4007 diode is probably the most popular of all diodes, since it is installed in the vast majority of chargers for phones, smartphones and tablets. Even if you’re holding a dollar charger and there’s no stabilization or interference filters inside, it can’t do without a diode. diodes have a peak repetitive reverse voltage of 50 volts, while 1N4007 diodes have a peak repetitive reverse voltage of 1000 volts. How much current can a 1N4007 diode handle? These are fairly low-speed rectifier diodes, being inefficient for square waves of more than 15kHz. [14] [ verification needed] They are not designed for switching applications; datasheets often do not specify any information on their turn-on and turn-off characteristics. [15]Datasheet" (PDF). Taiwan Semiconductor (TSMC). May 2014. Archived (PDF) from the original on 23 February 2018. Besides, it can also be used in any general application where there is a need for a general diode. The 1N4007 diode is designed to operate with high voltages and can easily withstand voltages below 1000V. The average direct current of 1000mA or 1A, the 3W power dissipation, its small size, and low cost make it an ideal diode for a wide variety of applications.