Simpson Strong-Tie Simpson-H2.5A-1/PACK H2.5A 18-Gauge Hurricane Tie, 1 Each

Product Information

In areas highly susceptible to strong hurricanes, installing hurricane ties on both sides of the wall is advisable. Simpson Strong-Tie offers stainless-steel Strong-Drive® SCNR Ring-Shank Connector nails. SCNR nails are available in paper-collated strips and in bulk for hand-drive fastening. See general fastener information. With a single-sided hurricane tie, you'll need to ensure that its length will work with your home. A tie that's too short will not be as effective. If you're not already remodeling your roof, you may need to remove the soffit or drywall to find the meeting place between the roof truss and wall. 2. Buying The Clips If, on the rare occasion we have delivered you faulty, incorrectly supplied or defective goods, Metro Fixings will arrange a collection, repair or replacement and delivery service free of charge.

Once you know how many hurricane ties and straps you need, you can mark their placement on the roof trusses. To do this, follow these steps: It also features a unique “twist” design, which adds strength and stability to the connection between the roof structure and the wall/joist. This twist design increases its resistance to uplift forces in case of a severe storm. How to Install Hurricane Straps and Ties

The rafter dimension isn’t limited to the width—the height matters as well. The height of the woodwork used as the bottom chord has to match the tie used for the nail holes to fit in properly. Should you discover that any item the Company has hired to you is apparently defective, you must inform us immediately. We may require you to return the item before the hire period is completed. We The primary function of hurricane ties is to establish a secure connection between the roof, walls, and foundation of a structure. In states where hurricanes are an annual threat, such as Florida, Louisiana, and coastal communities in the southeastern United States, hurricane ties are standard building requirements. They work by creating a load path that transfers forces from the top of the building to its foundation, significantly increasing structural stability during severe weather events. Any unenforceable or invalid provision or portion contained in the Agreement shall be deemed severed from the valid provisions which shall remain in full force and effect. You’ve now installed hurricane ties and straps on your roof, and you can rest assured that your home is better protected against high winds.

This is a straightforward process. However, you'll need to ensure that you're putting your selected clips in the correct place. Keep reading to learn more about how to install hurricane clips, where to put them on the beams, and more! How To Install Hurricane Ties and Clips 1. Determine The Number Of Clips You'll Need For properly-aligned frames, one strap will usually suffice. However, if they are out of place, you might need a different type of tie or multiple ties to attach both frames firmly. Choose the Nail Fasteners for the Hurricane Straps When retrofitting existing homes or during the construction of new homes, it’s essential to carefully evaluate the potential risk of high wind events in your area and consult with professionals to determine the appropriate level of reinforcement necessary for your specific circumstances. Retrofitting For Existing Homes: Two Methods For Installing Hurricane Ties There’s also gravity to think about. Those gravitational forces we mentioned earlier are pushing outward on each rafter, from peak to eave. By cutting a birdsmouth notch, those forces are redirected downward onto the wall plate and wall, which is exactly where you want those forcNext, position the hurricane tie on the top plate and rafters according to the manufacturer’s instructions. According to a roofing study reported by Treasure Coast Newspapers, an adequately reinforced and maintained roof can last 50-70% longer in a storm than an unprotected roof. That’s how much of an edge hurricane straps can offer in a hurricane.

The load distribution goes from the roof to the top then bottom of the wall, and finally ends in the foundation. This system gives the roof greater resistance against the upward wind force that could lift it off or the lateral force that could damage it in a hurricane.Research conducted by engineers at Texas Tech University found that houses secured with hurricane ties can withstand winds up to 130 miles per hour (209 kilometers per hour), significantly reducing the risk of roof failure and structural damage. Douglas, Howard. "Wood Frame Roof-to-Wall Connections". Florida Hurricane Retrofit Guide. Division of Emergency Management . Retrieved 23 May 2015. Seismic Technical Guide" (PDF). USGUSG Seismic Ceiling Resource Center. usg.com . Retrieved 23 May 2015. For a standard u-shaped hurricane tie, using 10 screws is recommended for maximum protection. Additionally, it’s important to reinforce the connection between the top plate and wall joists by installing additional ties if needed. The Company may repossess the goods at any time after your authority to possess or sell the goods under clause 7.4 above has been terminated or the Company’s termination of the Agreement under

Hurricane ties, also known as holdowns, are specialized metal connectors used in construction to secure roof trusses or rafters to the walls of a building and provide resistance against severe weather, including hurricanes and high winds.Another option you have to choose from is the H2 strap. These are installed on a vertical post perpendicular to a wall plate and a rafter. They have an uplift load of approximately 490 pounds and a lateral load of around 160 pounds. Many professionals often recommend an external installation unless it is impractical to retrofit the roof. In areas with severe hurricanes, you could even choose to go the extra mile and install the ties on both sides. Fasten the Ties in Place For stainless-steel fasteners, see Fastener Types and Sizes Specified for Simpson Strong-Tie Connectors. H2.5A hurricane ties are made from 18-gauge galvanized or stainless steel to prevent rusting and corrosion and ensure durability.