Three Flash Indicator Activation Time (0.05-12.75 sec) – How long you hold the indicator down for until 3 flash is de-activated If i mess up my ECU (for which i have not seen one single post that this has happened) then it will be my fault. So on Low Canbus i can goto some settings and onHigh Canbus i can goto the rest of the settings although i'm not sure what some of it is. What i will attempt to do is a guide for the FF2 (russian program) which will allow you to plug in a ELM 327 interface code reader into your focus Mk2 / Mk2.5 and update various parts of your car. Reverse Rear Wiper Initial Wipe (Enabled/Disabled) – If auto wipers enabled, and car is put into reverse, rear window wiper will wipe (if rain is detected)

I'm trying to enable cruise control on my Focus Mk2.5 1.6 TDCi, and am getting extremely slow speeds doing the initial step of "Read firmware from PCM to BIN-file". De-solder pin 14 from the OBD port (Make sure you label this wire if you have not used colour cable) I've explicitly set the adapter to use 500,000bps in ELMConfig, and it confirms that setting in the window titlebar. Below you’ll find what we believe are the best free ELM327-compatible software for Windows, Android, and iOS devices. Best ELM327 Software for Windows Smartphoneslove the post about follow the instructions to the letter. I have NEVER seen a complete set of instructions... that's the whole problem. Elmconfig is a program written by a guy on a Ford Focus forum (civil-zz) that uses the widely available ELM OBD reader/controller interface. Not only is this a useful DTC code reading tool but also a handy programming tool to modify various options and to enable features on Ford cars. Please do not attempt any mods unless you are comfortable to do so. Do any mods at your own risk.

Solder pin 6 (which you just de-soldered) to the middle pin on your switch (middle bottom in diagram) Do not change any options with RCM airbag module unless you know what you are doing""¦. Lets not switch any airbags off eh? bug: VIN wasn't read from factory AB file when loading it in some versions of the Central Configuration function However after the introduction of the MK3.5 some other people decided to make some changes to the FoCCCus program to add Focus MK3.5 support. These changes are included in the latest available FoCCCus version (which is not made by the original author). Unfortunately after a relative short time Ford changed the hardware and software version numbers again. These changes are never included in the FoCCCus program (and probably will never be included). Don’t get me wrong about Torque Lite. The free version of Torque is good enough for basic applications but it had trouble reading the trouble codes on some Nissan and Subaru vehicles.

I have a Ford Focus MK2 2.0 l petrol car. I tried for curiosity to write the odometer on my car, I was able to increase the km value, but not to decrease it from the “odometer write” menu. Than I tried to use the menu under IC programming, called “write odometer value in km” or so. As I wrote the former value from this menu, the decreasing also didn’t succeeded, but many problems came instead of. as I say may be wrong.... if I was right, the 2meg engine map would thus have or could have three elements to the map, I've copied and pasted this reply I had off @Dan P that sorted out my problems when I was having trouble, he was excellent, fair play to him. Install USB drivers for your ELM327 ( you may have to search for WIN 7 drivers) but it does work on Windows 7 Having connected the ELM327 module to the PC USB port and car OBD port and launched Forscan, I switched the ignition on when prompted – on my keyless start model this meant pressing the power button without pressing the clutch

Note: when connecting if FORScan says “No ELM Found”, flip the toggle switch to the other position and restart the connection process.If the OHP ELMconfig USB device connects, this is the HS-CAN position.Mark the adapter accordingly.

I then selected the Configuration & Programming menu from the vertical set of icons on the left of the Forscan window (the chip icon below the spanner icon) Turned on Ford Eco mode. Gives out a fancy set of icons with small flowers each flower has 5 sections one for gear , speed and anticipation. While the Car Scanner ELM ODB2 is still in Beta version as I speak, it managed to work very well in our Windows laptop and smartphone. We were able to diagnose the OBD2 fault codes and read the sensor data in our fleet of test vehicles without encountering unusual errors.

The FoCCCus software is no longer developed any further. There will never be full support for the MK3.5. Service functions HVAC "Actuators Calibration","Reset the Outside Air Temperature Sensor Learned Values" for: at this point Forscan showed a scrolling list of the modules it had found (after prompting me to toggle the toggle switch between MS & HS positions to complete the listing) Solder pin 14 (which you just de-soldered) to the other middle pin on your switch (middle top in diagram) The GEM Tab or (BCM) , This will not connect , and i'm Guessing that it needs the Wiring MOD before it can connect to the High CAN BUS.After you’ve paired the app with your scan tool, you can begin car diagnostics! image courtesy of Chris Running the Car Diagnostics with the ELM327 software These are the modules available to you in ELMConfig, most of them are pretty self explanatory. Not all modules will be fitted to all cars, for example, only the Kuga will have the AWD module. If your car doesn’t have a module, it doesn’t mean that it can’t be fitted and the functionality added to your car. There have been success stories of people adding cruise control to cars, and enabling it using ELMConfig. MS-CAN GEM